MagRing™ Magnetic Screw Holder Ring
Screws That Stay Put. Every Single Time.
You're halfway up a ladder. One hand on the drill, one hand holding yourself steady. The screw slips off the bit and bounces into the grass below.
Again.
This small aluminum magnetic ring slides onto your bit and creates a magnetic grip strong enough to hold screws in place — even when you shake the drill. No more fumbling. No more crawling around looking for dropped fasteners. Just slide it on, pick up the screw, and drive it home. Works with any standard 1/4" hex bit that's 2 inches or longer.
Ready to use the moment it arrives.
One of our most reordered tool accessories
✓ NO MORE DROPPED SCREWS MID-PROJECT
The magnetic ring creates a grip strong enough to hold standard wood screws, drywall screws, and machine screws — even when you tilt or shake the drill.
✓ FITS YOUR EXISTING BITS IN SECONDS
Slides onto any standard 1/4" hex bit that's 2 inches or longer. No adapters. No modifications. Just slip it on and go.
✓ ALUMINUM ALLOY THAT WON'T CRACK OR CRUMBLE
Unlike cheap plastic magnetizers that fall apart after a few uses, the metal housing is built to handle job site conditions.
✓ ONE HAND FREE FOR WHAT MATTERS
Hold the workpiece steady, brace yourself on the ladder, or position a bracket — while the screw stays locked on your bit waiting to be driven.
What you get today
- MagRing™ Magnetic Screw Holder Ring 1+1 Free
- Fits all standard 1/4" hex bits (2"+ length)
- Works immediately — no setup required
- Free tracked shipping
- 30-day money-back guarantee
Frequently asked questions
Will this work with short bits?
The ring is about 1 inch long, so you'll need bits that are at least 2 inches total length. Most impact driver bits and standard hex bits work perfectly.
Does it fit round shaft screwdrivers?
Yes, it fits most 1/4" round shaft screwdrivers as well as hex bits.
Will the magnetism wear off over time?
The internal magnets are permanent. The ring magnetizes your bit while in contact — remove it and the bit gradually returns to normal.
Can I leave it on the bit permanently?
Absolutely. Many users keep one ring on their most-used bit at all times.
How to use
- Step 1: Slide the ring onto your 1/4" hex bit from either end.
- Step 2: Position the ring near the tip of the bit for maximum magnetic hold.
- Step 3: Touch the bit tip to a screw — it will grab and hold.
- Step 4: Drive the screw as normal. The magnetic grip releases once the screw is seated.
Specifications
- Size: 0.9" height × 0.7" diameter (23mm × 18mm)
- Material: Aluminum alloy housing with internal rare earth magnets
- Compatibility: Standard 1/4" (6.35mm) hex bits, 2"+ length
- Weight: 0.3 oz per ring
Original: $19.99
-70%$19.99
$6.00
Description
Screws That Stay Put. Every Single Time.
You're halfway up a ladder. One hand on the drill, one hand holding yourself steady. The screw slips off the bit and bounces into the grass below.
Again.
This small aluminum magnetic ring slides onto your bit and creates a magnetic grip strong enough to hold screws in place — even when you shake the drill. No more fumbling. No more crawling around looking for dropped fasteners. Just slide it on, pick up the screw, and drive it home. Works with any standard 1/4" hex bit that's 2 inches or longer.
Ready to use the moment it arrives.
One of our most reordered tool accessories
✓ NO MORE DROPPED SCREWS MID-PROJECT
The magnetic ring creates a grip strong enough to hold standard wood screws, drywall screws, and machine screws — even when you tilt or shake the drill.
✓ FITS YOUR EXISTING BITS IN SECONDS
Slides onto any standard 1/4" hex bit that's 2 inches or longer. No adapters. No modifications. Just slip it on and go.
✓ ALUMINUM ALLOY THAT WON'T CRACK OR CRUMBLE
Unlike cheap plastic magnetizers that fall apart after a few uses, the metal housing is built to handle job site conditions.
✓ ONE HAND FREE FOR WHAT MATTERS
Hold the workpiece steady, brace yourself on the ladder, or position a bracket — while the screw stays locked on your bit waiting to be driven.
What you get today
- MagRing™ Magnetic Screw Holder Ring 1+1 Free
- Fits all standard 1/4" hex bits (2"+ length)
- Works immediately — no setup required
- Free tracked shipping
- 30-day money-back guarantee
Frequently asked questions
Will this work with short bits?
The ring is about 1 inch long, so you'll need bits that are at least 2 inches total length. Most impact driver bits and standard hex bits work perfectly.
Does it fit round shaft screwdrivers?
Yes, it fits most 1/4" round shaft screwdrivers as well as hex bits.
Will the magnetism wear off over time?
The internal magnets are permanent. The ring magnetizes your bit while in contact — remove it and the bit gradually returns to normal.
Can I leave it on the bit permanently?
Absolutely. Many users keep one ring on their most-used bit at all times.
How to use
- Step 1: Slide the ring onto your 1/4" hex bit from either end.
- Step 2: Position the ring near the tip of the bit for maximum magnetic hold.
- Step 3: Touch the bit tip to a screw — it will grab and hold.
- Step 4: Drive the screw as normal. The magnetic grip releases once the screw is seated.
Specifications
- Size: 0.9" height × 0.7" diameter (23mm × 18mm)
- Material: Aluminum alloy housing with internal rare earth magnets
- Compatibility: Standard 1/4" (6.35mm) hex bits, 2"+ length
- Weight: 0.3 oz per ring
